人気ブログランキング | 話題のタグを見る
ブログトップ

磨墨(するすみ)の秘密基地

surusumi.exblog.jp

家作り備忘録93A selfbuilder's note

母屋が上がり、これで構造体の設営は一通り終わり、この構造体を包む部分、つまり屋根や外壁の工事に移行出来る様になった。と言っても、まだまだ構造体部分との関わりは続く。
家作り備忘録93A selfbuilder\'s note_b0229636_192297.jpg


屋根垂木を仮付けして、垂木彫りの角度や、屋根全体の勾配にちゃんと合っているか確認です。なんとか合っているようです。ほっ。(~_~;)
家作り備忘録93A selfbuilder\'s note_b0229636_191492.jpg

それでは、じゃんじゃん取り付けて行きましょ〜。これは面白い様に進んで行きます。構造体と違って、外側は進捗が目眩く程、次々に出来上がって行くのが見えて、今迄の地道な作業がウソのようです。
家作り備忘録93A selfbuilder\'s note_b0229636_1914936.jpg

いい感じです。あの上に屋根が載ると思うと、ワクワクする。
家作り備忘録93A selfbuilder\'s note_b0229636_1915068.jpg

ほれっ、もう半分付きました。早い、早い。
家作り備忘録93A selfbuilder\'s note_b0229636_192312.jpg


たまたま休みだった会社の同僚が、愛犬のGooちゃんを連れて来て、家内も2ワンズと一緒に基地入りしてたので、みんなで建築中の家の中でお昼ご飯を食べて、ワンズは近所の公園を散歩。楽しいひと時だった。
家作り備忘録93A selfbuilder\'s note_b0229636_1915235.jpg

家作り備忘録93A selfbuilder\'s note_b0229636_1915339.jpg

垂木は全長が6m30cm程あるので、定尺の材では足りず、3mと4mの材を繋いでいます。下側の女木に上側の男木が乗り、それを屋根垂木専用の長いビス165mmで真ん中を貫通させて、母屋に固定します。インパクトは、現在市場では最強のトルクを誇る、マキタのコード式ドリル。ガンガン留まって行きます。充電式が全盛のインパクトドリルに、コード式?と思うかも知れませんが、コードも長く、柔らかいものを使っているので、自由度に遜色ありません。しかも、電池切れの心配が無いので、作業に没頭できる。
家作り備忘録93A selfbuilder\'s note_b0229636_1915438.jpg

垂木が全部載った!と言っても、2段構造の屋根の下側の段だけですが、やっと
家の全体像が見えて来た。
家作り備忘録93A selfbuilder\'s note_b0229636_191557.jpg

玄関アプローチだけは、庇部分が突き出し、露出する為、防腐、防水塗料を塗ってあります。この上に、さらに垂木を横に打ち付け、ポリカーボネートの波板が乗る予定。
家作り備忘録93A selfbuilder\'s note_b0229636_1915516.jpg

屋根垂木が載ったら、次は下地合板の張り付け。エアコンプレッサーと自動釘打ち機の登場。コンプレッサーは基地から運び出すのに、近所のヒデさんに手伝ってもらいました。業務用の釘打ち機が使えるクラスですが、とにかく重い。釘打ち機も、90mmの釘を打てる常圧タイプでは最強。今後、仕上げまで活躍してくれると思います。
家作り備忘録93A selfbuilder\'s note_b0229636_191572.jpg

横長の板を繋いで打ち付けて行くには、最初の一列が真っ直ぐ張れるかどうかが鍵になります。そこは慎重に、ゲージを当てながら、水平を確認しながら打って行く。下地合板の下端が揃う様に垂木を当ててあるので、落下の心配はありません。
家作り備忘録93A selfbuilder\'s note_b0229636_1915859.jpg

一段目がなんとか真っ直ぐ張れたので、2段目は早かった。その朝一番で、煙突の外枠を取り付けています。
家作り備忘録93A selfbuilder\'s note_b0229636_1915974.jpg

さて、ここから斜面に身を投げ出す事になるので、ハーネスを着けて、セルフビレイ、つまり自己確保を取りながら、屋根面に出ます。たまに、自分がクライマーで良かったと思う瞬間です。^o^
家作り備忘録93A selfbuilder\'s note_b0229636_192021.jpg

9連休の最終日。あっと言う間でした。昨日の続き。3段目まで行って、トラブル発生。コンプレッサーの調子が良く無い。基地のアンペアが20Aしか無いので、エンジンが回り始めると、負荷が大きくて、ブレーカーが落ちてしまうを繰り返して、何度も作業が中断。困った!先に進めない。関電に工事現場用の電源を引いて貰おうか?今回はこれまで。梅雨前に屋根が上がるのか?とりあえず養生して帰ろう。
家作り備忘録93A selfbuilder\'s note_b0229636_192118.jpg

ミョウガが大きくなってる。夏が近い。

Roof support beams were done. Thus, entire skeleton of this house all settled. Now I can move onto the 'shell' of the house. First , I need to work on its roof. Since, once canopy installed, whole structure will be covered from rain. So I had to be very in a hurry to finish roofing.

First checking if the gradient of roof support rib matching with the slant lane of supporting beams as well as the top notch beam. I've been anxious about this fit. Looks like it goes well. Phew!

OK. Let's install ribs without hesitation. It goes real quick. What the hell was that slow process of fixing skeletons? Now I'm enjoying best part of building a house. Nothing but fun.

Good view from the center floor. Exciting to imagine the roof will be on those ribs. Well, whole roofing procedure starts from installing those ribs. Then, hammered plywood board for roof insulation base. Water proof/breathable non woven fabric will follow. After the fabric tuckered, insulation boards inserted. Then the top roof ribs will follow. Same procedure will be taken except insulation board inserting until roof shingles covers the top surface.

Half of whole ribs has been settled in a day. Took a lunch at the constructing house with my wife and a friend who also owns Labrador visited me by chance.

The roof rib material isn't long enough for length of shed. Two pieces joined at roof support beam and connected with big screw. The screw is so long and big that any normal impact drivers could not handle. I bought the strongest torqued impact driver on the market for this house building. And the driver works pretty much satisfactorily. Corded but no problem with its maneuverability. Another good choice I've made for sourcing equipments.

Roof ribs for the first layer all settled. Now the entire image of my new house appeared.

Except entrance approach, the first layer ribs supports its half-clear roofing. Material to be polycarbonate. As it's exposed, ribs must be painted with water proof oil stain. Ribs accept cross ribs to support the roofing.

Next stage for roofing to be surfacing with plywood board for under layer of breathable non woven fabric and insulation boards. I need air compressor for the job. Heavy duty air nailer plays important roll for surfacing the plywood layer. Mines up to 90mm nail could be handled.

When placing long line of wood panels, the beginning line must be nailed straight enough. This first line decides entire finish. So I got to be very careful about the nailing with measuring horizontal line by gauge time to time.

Once the first line placed well, the second line was easy. First that morning, chimney top box was also installed.

Now I have to expose myself into the roof. Self belay needed to be taken. I'm glad that I was a rock climber.

The very last day of my 9 days off. It all went so quick! When third line of plywood on nailing, problem took place. Air compressor started breakdown when recharging air. Causing lots of delay. Muu. I need to solve this situation ASAP. Maybe asking power supplier to install temporally outlet with higher voltage? Well, I must consult with my friend for this.
by blacklabsurusumi | 2014-05-11 17:18 | セルフビルド
<< 家作り備忘録94A selfb... 家作り備忘録92 A self... >>